Delivering High Quality Flow Meter Orifice Plates in Paddle Type, Restriction, Ring Type Integral, Concentric Bore, Eccentric Bore, Segmenta, Quadrant etc.
Vimek Industries Logo, Restriction Orifice Plate Supplier

Are you Looking to Buy Orifice Plate for Orifice Fittings (Buy Now Our Expertise Piping Products)

Vimek Industries is specialized in Manufacturing and Supplying of Orifice Plate, Stainless Steel Orifice Plate, Carbon Steel Orifice Plate since 1991, we manufacture wide range of Orifice Paddle Plate, Paddle Type Orifice Plate, Restriction Bore Orifice Plate, Concentric Bevel Bore Orifice Plate, Eccentric Bevel Bore Orifice Plate, Segmenta Bore Orifice Plate, Quadrant Bore Orifice Plate, Ring Type Joint Integral Orifice Plate etc.


ORIFICE PLATE :
Orifice Plate is the heart of the Orifice Meter. It restricts the flow and develops the Differential Pressure which is proportional to the square of the flow rate. The flow measuring accuracy entirely depends upon the quality of Orifice plate, its installation and maintains. When measuring wet gas or saturated steam a weep hole is drilled in a concentrically bored orifice plate. This is a small hole drilled on the orifice plate such that its location is exactly on ID of the main pipe. The Orifice plates are manufactured as per ISA / AGA/ API / ANSI standards and in various materials such as SS304 /SS316 / SS316L /Hestoly C / Monel / ASTM A516 Grade 70 etc.

RESTRICTION ORIFICE PLATE :
A Restriction Orifice Plate is similar to an orifice plate but is much thicker. It is used to drop upstream pressure of a system. While passing the fluid through thick plate energy is lost in friction and heat resulting considerable pressure drop.

Normally single Orifice Plate having larger Thickness is used. However when the Flow velocities crosses the limit of critical flow and are subjected to sonic velocities to avoid noise vibration and cavitations in the liquid the Restriction Orifice Plates are designed in multistage form. For Viscous fluids and low Reynolds number the upstream side of the Restriction Orifice plate is beveled.

The discharge coefficient of the restriction orifice plate is, also as per the orifice plate, approximately 0.6 according to ISO 5167. The bore is designed as per ISO 5167 and thickness as per R.W Miller/Ward-Smith.

When the noise through single hole is beyond the acceptable limit sometimes Multi Hole plates are used as restriction orifice plates .The process condition defines the no of holes. Multistage with multi holes restriction is also a possible combination.


Stainless Steel Orifice Plate

High Quality Orifice Plate in Stainless Steel Grade like 304, 316L, 310S, 321, 347, 904L etc.as well Dual Grades Like, 304/304L , 316/316L. we keep in house huge Inventory of Stainless Steel Plate of Manufacturer like Jindal / Posco / Aperam Stainless / Tsingshan etc.


Read More...

Carbon Steel Orifice Plate

we Supply Structural and Carbon Steel Orifice Plate in Specification Like IS 2062 E250, IS 2062 E350, ASTM A516 Grade 70, ASTM A36 etc. we Stock Raw Material of Essar / Jindal / SAIL / POSCO etc. we Carry Multiple Sizes in Carbon Steel Orifice Plate.


Read More...

Paddle Type Orifice Plate

They are used for creating a differential pressure drop in which to measure the flow rate between two points located at the pressure taps of orifice flanges. Turn Down Rate for orifice plates are less than 5:1. Orifice plates used for flow measurement require a bevel on the downstream side.


Read More...

Concentric Bevel Bore Orifice Plate

This most common bore used in the industries. This is the only type generally accepted for use in custody transfer measurement, since adequate data is not available for other bores. Used primarily for clean homogeneous liquids, gases, non viscous fluids. The bevel is matched at 45o angle to the desired throat thickness.


Read More...

Eccentric Bevel Bore Orifice Plate

Used for measurement of flow for fluids containing solids and slurries. It is also used for vapors and gases where condensation is present. The eccentric bore is offset to where the bore edge is inscribed in a circle that is 98% the line id.


Read More...

Restriction Bore Orifice Plate

This type is not used for flow measurement but for dropping the pressure considerably and reducing the flow accordingly. The bore is not beveled but kept straight. The beta ratio has no limit as accuracy is not the goal.


Read More...

Segmental Orifice Plate

The segmental bore is located in the same way that the eccentric bore is. This type is used primarily for slurries or extreamly dirty gases wher the flow may contain impurities heavier than the fluid.



Read More...

Ring Type Joint Integral Orifice Plate

These are available in oval or octal shapes. Orifice plate is a part of RTJ gasket..






Read More...

Why Choose Us?

Quality Products

  • Quality Certified Materials
  • Marking, Heat Number, Specifications, Grade
  • Full Traceability of Material
  • Third Party Inpection / Buyer Inspection
  • NDT, Destructive Test Reports
  • Conformity to ASTM, ASME, DIN, EN, JIS, SUS
  • Test Certificate as per EN 10204 3.1 / 3.2

Best Selling Products

  • 304 Orifice Plate
  • 316L Orifice Plate
  • 304/304L Orifice Plate
  • 316/316L Orifice Plate
  • ASTM A516 Grade 70 Orifice Plate
  • Quadrant Orifice Plate
  • Ring Type Joint Seperated Orifice Plate

Expertise

  • No Minimum Order
  • Material from Reputed Mills and Manufacturer
  • Products with Accurate Dimension
  • Abundant Stock, Immediate 'On Time' Delivery
  • 35 Years of Supply and Export Experience
  • Sourcing even Hard to Find Items
  • Warranty and Guranteed for Any Material Defect

Supplying Countries & Cities

UAE, Bahrain, Italy, Indonesia, Malaysia, USA, Singapore, Philippines, Mexico, China, Brazil, Peru, Nigeria, Kuwait, Jordan, Oman, Muscat, Dubai, Thailand, Venezuela, Iran, Germany, UK, Canada, Russia, Turkey, Australia, New Zealand, Sri Lanka, Vietnam, South Africa, Kazakhstan, Saudi Arabia, Algeria, Angola, Congo, Kenya, Sudan, Poland

Mumbai, Delhi, Bangalore, Hyderabad, Ahmedabad, Chennai, Kolkata, Surat, Pune, Indore, Thane, Bhopal, Vadodra, Nashik, Faridabad, Rajkot, Ranchi, Coimbatore, Raipur, Mysore, Bhubaneswar, Salem, Bhilai, Kochi, Bhavnagar, Siliguri, Visakhapatnam

Vimek Industries

4th Floor, Platina, G Block,
Bandra Kurla Complex,
Mumbai - 400051. Maharashtra. INDIA


Tel:


Email: sales@vimekindustries.com

Web: www.vimekindustries.com


ISO 9001
ISO 14001
OHSAS 18001
PED-97/23/EC